Pinball Xperience

First Pinball Machine Toolbox: Essential Tools Every Owner Need

· Lazarvs

First Pinball Machine Toolbox: Essential Tools Every Owner Need
pinball xperienceTuto flippermaintenance flipperpinball maintenancedébuter au flipperpinball for beginnersPX Academy

So yes, you’re right, I put all my know-how, impeccable taste, and finest references into this thumbnail, but it’s for a good cause! Because the whole point is to get you to read my articles and, hopefully, help you along the way. And let me tell you, once you’ve finally managed to drag your eyes away from the thumbnail, you’re almost certainly looking at the single most important article for anyone thinking about buying their first pinball machine. It’s: the handywoman, uhhh... oops... I’m getting distracted. No, not at all, sorry, Freudian slip! It’s: the toolbox!

Your first pinball machine has just arrived. It’s set up, leveled, plugged in, and you’ve already spent a perfectly unreasonable amount of time watching the ball travel around the playfield. Then bam, your first suspicious noise, instantly taking you back to that slightly awkward moment from childhood when you heard something squeaking behind your parents’ bedroom door, something halfway between human and mechanical, but with all the innocence of youth you shouted: “Mom, Dad, something’s squeaking in your bedroom!” And then, strangely enough, the noise stopped and, miracle of miracles, life went back to normal...

Well, pinball is a bit like that, except for the ending. The noise doesn’t stop, and this time you’re going to have to open the door, the coin door, and find out what’s actually going on.

Very often, it’s nothing serious. A screw has worked itself loose, a nut has fallen under the playfield, a switch doesn’t seem to be responding properly. The real fun begins afterward. You open your toolbox and discover a full-size hammer, three Phillips screwdrivers that are way too big, and an Allen key that apparently came with a piece of furniture you bought eight years ago. In other words, absolutely nothing designed for delicate work. So yes, it’s time to gear up.

Owning a pinball machine doesn’t mean immediately turning your garage into an electronics workshop. For routine maintenance, basic adjustments, and your first repairs, a relatively compact toolbox is enough. What matters isn’t owning fifty tools, it’s having the right ones when a simple problem comes up. Your equipment will grow along with your skills. You’ll start with a few screwdrivers, wrenches, pliers, and cleaning products. The multimeter and soldering iron can come later, once you want to learn how to diagnose and repair more things yourself.

The goal isn’t to buy an entire tool supplier’s catalog before you’ve even played your hundredth game. It’s to build the first proper toolbox of a pinball owner, versatile enough to maintain your machine, handle basic jobs, and gradually learn without turning every loose screw into a service call.

Start with the right screwdrivers

The screwdriver remains one of the fundamental tools. You’ll encounter different screws throughout the cabinet, playfield, plastics, and various mechanisms. An assortment of several sizes will already cover a huge number of everyday jobs. Choose decent-quality tools with tips that actually match the screw heads found on your machines. A comfortable handle and properly machined tips matter far more than a box containing 150 bits when 148 of them will never leave their slots.

Size deserves more attention than it usually gets. Using a tool that’s “close enough” increases the risk of damaging the screw head, slipping onto a nearby part, or making the next disassembly considerably harder. If a screwdriver doesn’t properly engage with the screw head, the solution is rarely to push harder with even greater conviction. Identify the fastener and use the right tool.

The screws holding plastics and decorations are often difficult to reach, so go for long screwdrivers. What? You want a reference? Fine, get yourself a Phillips Screwdriver PH2 x 150 mm. Coming soon right here, because I’m getting tired of giving everyone else free advertising out of the goodness of my heart when nobody ever returns the elevator. Eventually, you realize you’re not living in an apartment building, you’re living in a bungalow. With this one, you can handle almost every Phillips screw on a pinball machine.

Nut drivers quickly become indispensable

A nut driver looks like a screwdriver with a socket on the end. It allows you to quickly tighten and loosen the nuts and various hex fasteners found all over a pinball machine. It’s exactly the kind of tool many new owners don’t have before buying their first machine, then end up using constantly afterward.

You may need several sizes depending on your machines. Measurement standards can also vary depending on the manufacturer, origin, and generation. Check your machine’s documentation and identify the sizes actually used rather than buying randomly. A properly selected set makes jobs much faster and, more importantly, removes the temptation to attack every nut with a pair of pliers. Once you’ve used the correct nut driver in a cramped area of the playfield, you’ll understand why your universal pliers belonged to a more primitive period of your existence.

What? You want a reference? Fine, get the Hexagon Socket Wrench 1/4" x 125 mm and the Hexagon Socket Wrench 5/16" x 125 mm. Coming soon right here, because I’m getting tired of giving everyone else free advertising. Philanthropy is wonderful, but normally there’s a tax deduction involved !

Add sockets, combination wrenches, and Allen keys

A small ratchet with suitable sockets perfectly complements your nut drivers. It becomes useful when you need more control, a different angle of access, or when a fastener requires something more substantial. There’s no need to drag a heavy-duty truck mechanic’s toolkit under your playfield. A compact set covering the sizes actually found on your machines is more than enough to get started.

You’re starting to know me by now, I don’t really do half measures. I like bespoke. So I’m putting the ratchet I personally use here, but feel free to buy a cheaper one.

A few open-end or combination wrenches are also useful, especially when a nut needs to be held while you work on the fastener from the opposite side. Finally, add a set of Allen keys for components using hex socket screws. Pay close attention to metric and imperial standards. Some sizes are close enough to make you think the wrong key works, right up until it starts rounding out the socket. Spending a few seconds identifying the correct size is considerably less painful than spending twenty minutes wondering how to extract the screw you personally just sentenced to death.

Three pairs of pliers already cover a lot of situations

A pair of needle-nose pliers quickly becomes one of a pinball owner’s best friends. It lets you grab small parts, hold a nut, retrieve something from a narrow space, or manipulate components that are difficult to reach. Space under a playfield is rarely generous. Mechanisms, brackets, and wiring harnesses create plenty of places your fingers physically refuse to enter. Personally, I added rubber to both sides of the jaws, similar to a cooktop seal, to avoid marking components if I squeeze a little too hard.

Add a small pair of cutters if you start working with wiring or cable ties, then wire strippers when you move on to minor electrical repairs. Wire strippers aren’t necessary for cleaning a playfield or replacing a rubber, but they become extremely useful once you start learning how to properly repair a wire. Before cutting anything, obviously identify what’s in front of you. Discovering that the wire you deliberately cut wasn’t the one you thought it was makes for an excellent forced introduction to soldering, but it’s a fairly questionable teaching method. There are even two-in-one pliers that handle both jobs.

Add a few precision tools

A good pair of tweezers may seem insignificant among all those wrenches and screwdrivers, right up until a tiny washer falls into the single least accessible place in the machine. Tweezers let you manipulate small parts, position components, and work in particularly tight spaces. A straight pair is enough to start with, possibly supplemented by angled tweezers if you regularly work beneath the playfield. Personally, occupational habits die hard, so I prefer using clamp forceps. I handle them every day and have much better dexterity with them than with tweezers, but that’s entirely up to you.

A small adjustable telescopic inspection mirror is also surprisingly useful. Some areas remain difficult to see even with good lighting. Before removing an entire ramp because you think there’s a loose screw behind it, the mirror may allow you to confirm the problem. The less you dismantle unnecessarily, the fewer opportunities you create to discover, once everything is back together, that one mysterious washer is still sitting on your table. You can even find models with a small built-in LED.

Buy a good light before buying exotic tools

Under the playfield, inside the cabinet, or behind the backbox, the available lighting isn’t always enough to work properly. A small adjustable LED light or headlamp quickly becomes extremely useful. The obvious advantage of a headlamp is that it leaves both hands free, even if it immediately makes you look like someone heading off to explore a mine shaft beneath their Godzilla.

Good lighting also makes diagnosis easier. You can better see a screw, connector, wire, crack, or the exact position of a mechanism. Before deciding that a problem requires sophisticated equipment, make sure you can actually see what you’re doing. A surprising number of jobs become much easier once the area you’re working on is no longer buried in darkness.

The magnetic pickup tool will save your back and your patience

Now this is a must-have! You remove a screw. It falls. You hear it bounce once inside the cabinet, then nothing. Silence. It has officially entered the parallel dimension where all missing pinball parts apparently live.

A small telescopic tool with a magnet can save an enormous amount of time when a screw, nut, or metal washer falls somewhere inaccessible. Obviously, it won’t work with every material and should be used sensibly around the machine’s various components, but when you need to retrieve a metal part from the bottom of the cabinet, it can turn fifteen minutes of searching into a few seconds. It won’t be the most spectacular tool in your box. Sometimes, it’ll be the one you love the most.

Organize your hardware instead of trusting your memory

Use small containers, compartment boxes, or bags to keep screws and parts organized during a job. If you dismantle several areas, keep their parts separate. A small magnetic tray can also be useful for certain metal parts, provided you use it in an appropriate environment and keep it away from areas where a magnet has no business being.

Professor Pinball’s little tip: if you don’t have a magnet, use the magnet from the subwoofer.

Don’t just dump all the hardware onto a table and tell yourself you’ll remember exactly where everything goes. You won’t. And that screw that’s slightly longer than the others had a reason for being slightly longer than the others. A little organization during disassembly saves a lot of questions during reassembly.

Your smartphone is already one of your best tools

Before dismantling anything, take pictures. Start with an overall shot, then take close-ups. Photograph cable positions, washer order, mechanism orientation, connector routing, and any assembly you might forget. If the job gets more complicated, taking a few extra pictures costs considerably less than spending an hour searching online for a reference image.

Your phone effectively becomes your own reassembly documentation. Human memory has a fascinating amount of confidence when you remove four different spacers. Two hours later, when those same four spacers are sitting in front of you and three suddenly look like they could fit in the exact same place, that confidence tends to disappear.

Keep microfibers in the toolbox

A few clean microfiber cloths reserved specifically for your pinball machines are an obvious basic. Ideally, separate them according to their purpose so you don’t accidentally transfer products or residue from one surface to another. A microfiber cloth that has just cleaned a particularly dirty part of the machine doesn’t necessarily need to immediately continue its career on a delicate surface.

The important word here is clean. Rubbing a playfield with a microfiber cloth already containing particles capable of scratching the surface is an impressively elaborate way of turning maintenance into the exact opposite. Keep several cloths available, wash them properly, and store them away from dirt when you’re not using them.

Cleaning products should be chosen for your machine

There is no single universal product that should be applied everywhere inside a pinball machine. The playfield, glass, cabinet, metal parts, display, and various plastics may require different methods. Recommendations also vary depending on materials, finishes, and generations.

Your maintenance kit should therefore contain products appropriate for your machines, selected according to the manufacturer’s documentation and reliable recommendations for the surfaces concerned. Avoid experimenting with the first household cleaner you find under the sink. A pinball machine is not a kitchen countertop with flippers attached.

A few soft brushes reserved for this purpose can complete the kit. They allow you to gently remove dust from hard-to-reach areas before carrying out a deeper clean. A small manual air blower can also be useful for moving particles without blasting excessive pressure into mechanisms or electronics.

A digital level lets you set up the machine properly

A pinball machine’s setup directly affects its gameplay. Pitch and side-to-side leveling change the speed and trajectory of the ball. A machine that leans slightly to one side can favor certain trajectories and make other shots more difficult without the problem being immediately obvious.

A digital level is therefore an excellent investment. It allows you to check the setup after moving the machine, adjusting the leg height, or simply whenever the ball starts behaving strangely. Before accusing the designer of creating an orbit incapable of working properly, make sure your machine isn’t sitting there with the geometry of a camping table.

The multimeter marks your first step into diagnostics

The multimeter becomes essential once you want to go beyond purely mechanical maintenance. It allows you to perform various electrical measurements and, among other things, check continuity as part of a proper diagnostic process. Whether you’re looking for a broken wire, testing certain fuses outside the circuit, or following a troubleshooting procedure from the documentation, it quickly becomes indispensable.

But owning a multimeter doesn’t automatically mean knowing how to use one. Incorrect settings, improper measurement methods, or working in a powered area without sufficient knowledge can pose risks both to you and to the machine. Learn how it works before poking the probes everywhere and hoping the numbers on the display will eventually reveal the problem through divine intervention. The tool gives you a measurement, interpreting it remains your job.

The soldering iron comes when you’re ready to use it

The vibrations and movements of a pinball machine can put stress on connections throughout its life. A disconnected wire is therefore one of the problems an owner may encounter. Knowing how to perform a proper small soldering job becomes a very useful skill.

A suitable soldering iron, accompanied by the necessary equipment and used correctly, allows you to perform certain accessible repairs. But soldering requires a minimum amount of practice. Train on something worthless before approaching an expensive or difficult-to-replace component. Repairing a disconnected wire is an accessible skill. Simultaneously discovering how a soldering iron works while holding it over your pinball machine’s circuit board represents a level of self-confidence the situation absolutely does not require.

If you start soldering, also add the equipment needed to desolder properly. A desoldering pump or braid allows you to remove solder during certain jobs and correct imperfect work. Learning to solder also means accepting a fairly healthy truth: not every one of your first solder joints deserves to become a permanent part of the machine.

Only keep fuses that actually match your machines

Keeping a few replacement fuses can be useful, provided they exactly match the specifications required by your pinball machines. A fuse has a specific rating and type designed to protect a circuit. Never replace one with a higher rating simply because you don’t have the correct one available.

If a fuse blows again after replacement, you need to investigate the cause. Repeatedly replacing fuses or changing their rating isn’t troubleshooting. The fuse isn’t the enemy preventing your pinball machine from working, it’s often the component preventing a small fault from turning into something considerably more financially interesting.

Gradually build a small stock of consumables

As you become familiar with your machines, you can keep a few genuinely useful consumables and common parts on hand: suitable pinballs, specific rubbers, correct fuses, and other components matching your collection. A small stock can sometimes let you fix a problem immediately instead of waiting for an order to arrive.

There’s no need, however, to turn your first toolbox into a spare-parts warehouse. Buy according to your needs and the specifics of your machines. Owning fifteen references that are incompatible with your pinball machine isn’t preparedness. It simply means you now own inventory whose purpose even your machine doesn’t understand.

Cable ties, masking tape, and labels: small details that prevent mistakes

A few cable ties can be useful for putting wiring harnesses back in place when the machine’s configuration requires it. Use them sensibly and don’t tighten the cables as though they’re trying to escape. Before changing the route of a wire, also consider why it was routed that way in the first place. What looks like a pointless detour may simply be keeping it away from a moving part.

Masking tape and a few labels also become extremely useful when disconnecting several similar components. A number or note on each connection lets you quickly identify where it belongs. Combined with the photos taken on your phone, this creates simple and extremely effective documentation. The best reassembly mistake is still the one you prevented before it ever existed.

A caliper becomes useful sooner than you think

A small caliper isn’t essential for cleaning your first playfield, but it becomes useful once you start identifying screws, spacers, rubbers, or other parts whose exact dimensions you don’t know. It provides far more reliable measurements than an estimate made with a ruler and an unhealthy amount of optimism.

It’s also useful once you begin ordering more parts or carrying out more advanced work. Like many items in this toolbox, there’s absolutely no reason to buy one immediately if you don’t need it. Your equipment should evolve alongside your skills and the jobs you actually perform.

The manual belongs in the toolbox

Your machine’s manual isn’t a mechanical tool, but it deserves a permanent place in your working environment. It may contain part references, diagrams, wiring information, diagnostic procedures, and other data specific to your model.

Keep a digital version easily accessible whenever the manufacturer provides one. If you regularly work on a machine and have the relevant documentation, you can also keep the most useful pages nearby. The Internet contains a gigantic amount of information and advice. The manual, however, has one rather pleasant advantage: it actually concerns the machine sitting in front of you.

What you actually need to buy first

You don’t need to buy everything immediately. For your first pinball machine, focus on a good assortment of screwdrivers, the nut drivers and wrenches that match your machine, needle-nose pliers, a light, a few precision tools, clean microfiber cloths, appropriate cleaning products, containers for hardware, and a digital level. That kit already allows you to handle a large part of routine maintenance and the small jobs accessible to a beginner.

The multimeter, wire strippers, and soldering equipment come later when you want to move into electrical diagnostics and certain repairs. Buy them alongside the knowledge required to use them. Your toolbox will naturally evolve with your experience and the specifics of your collection. That progression makes far more sense than immediately buying a gigantic generic toolkit when half of its contents don’t fit a single fastener on your machine.

A dedicated toolbox changes everything

Once you’ve assembled your equipment, keep it together. A toolbox or small dedicated tool cart for pinball allows you to keep your everyday tools, consumables, microfiber cloths, and small parts in one place. When a problem appears, you grab your kit and immediately have the essentials at hand.

With several machines, your equipment will naturally expand. A small work area may eventually become worthwhile, and specialized tools will gradually join your collection. But when you’re starting out, a properly organized toolbox already covers an enormous number of situations. The goal isn’t to own an impressive workshop. It’s to avoid spending twenty minutes looking for the right screwdriver while your pinball machine sits open in the middle of the room.

And WD-40? Yes, I use it

Let’s finish with a product that has the remarkable ability to turn a discussion about pinball maintenance into an international summit on cyberbullying and public lynching: WD-40. The second its name appears, some self-appointed little prosecutor with a pencil-thin mustache emerges from the East, usually to explain that you should “NEVER put that in a pinball machine,” immediately joined by his pack of digital dachshunds, all incredibly brave as long as there are fifteen of them barking from behind a screen. The most fascinating part is what happens once the noise dies down and you ask the most basic question of all, “why?” The argument usually melts away considerably faster than their confidence. Considering the level of certainty they were displaying thirty seconds earlier, that’s quite an achievement.

If you see this man, don’t let him wind you up, he’s only trying to rewind you.

“Topurz iz 4 suckerz.” Note for English-speaking readers: translation of what he wrote on his sign.

Let’s start with a fact: contrary to one particularly stubborn myth, WD-40 Multi-Use Product is indeed a lubricant. The manufacturer describes it as a mixture containing lubricating oils, while also providing penetration, moisture displacement, and corrosion protection. WD-40 itself states that the product is intended, among other uses, for lubricating moving metal parts.

Personally, I use it with great satisfaction on certain very specific moving metal components. On my Jaws, for example, the moving parts of the reels and the bar responded spectacularly after a very light application to their ball bearings. The same principle applies to certain shafts or spinners when this type of lubrication is appropriate. Obviously, we’re not talking about opening the can above the playfield and baptizing the machine in WD-40. A few drops exactly where they’re needed have absolutely nothing in common with spraying an entire mechanism.

The important thing is to stop confusing “WD-40 can lubricate” with “WD-40 should be used everywhere, like greasing the bottom of a casserole dish so the gratin doesn’t stick.” Absolutely not. A coil, circuit board, contact, or mechanism for which the manufacturer specifies a different maintenance procedure doesn’t suddenly become a candidate simply because it happens to live under the same playfield. Some mechanisms are designed to run dry, others require a specific lubricant. My experience using it on spinner shafts, for example, is therefore my personal experience, not a manufacturer’s recommendation.

Another objection regularly raised concerns flammability. That one is absolutely real: the safety data sheet for WD-40 Multi-Use aerosol classifies it as an extremely flammable aerosol and requires it to be kept away from heat, sparks, and flames. That isn’t something to dismiss. It’s one more reason to use it intelligently, with the machine powered off during the intervention, in tiny quantities and only on an appropriate part, rather than proof that the product is somehow incapable of lubricating anything.

WD-40 is therefore neither holy water nor Satan’s own personal lubricant. It’s a product with defined properties, appropriate uses, and safety precautions. As with any lubricant, you first determine whether the part actually needs lubrication and what product should be used. Only then do you reach for the can.

And if someone tells you that “WD-40 isn’t a lubricant,” you can at least save them twenty minutes of debate: even WD-40’s own manufacturer says otherwise.

The most important tool is still the one you know how to use

Owning tools doesn’t automatically turn a pinball owner into a technician. For every job, start by understanding the problem, consult the appropriate documentation, and use the tool that actually matches the task. If you need to work in an electrical area or on a mechanism you don’t understand, learn the procedure before touching it or leave the job to someone competent.

You’ll quickly discover that a large part of routine maintenance remains accessible. Properly tightening a fastener, cleaning the playfield, replacing a wear part, checking a switch, or putting a component back into place doesn’t require a professional workshop. What matters most is method, patience, and the extremely profitable habit of photographing things before taking them apart.

A few months after buying your first machine, your little toolbox will undoubtedly contain more tools than it did at the beginning. You’ll know what they’re for, recognize the main fasteners used throughout your machine, and start diagnosing problems that would have seemed completely incomprehensible during your first week. Don’t forget, we all started somewhere, and we’re here to help you.

Thus have I spoken.

Lazarvs

The author

Lazarvs

Fondateur de Pinball Xperience. Joueur. Collectionneur. Créateur. Le flipper comme jeu, culture et industrie. PLAY. LEARN. CONNECT.

View profile