Pinball Xperience

Tutorial | How to Install a Speaker Light Kit on a Stern Pinball Machine

· Lazarvs

Tutorial | How to Install a Speaker Light Kit on a Stern Pinball Machine
stern pinballpinball xperienceTuto flipperpinball tutorialPX WorkshopElvira's House of Horrors

Tutorial | How to Install a Speaker Light Kit on a Stern Pinball Machine

In the pinball community, you have the tinkerers, the people who seem to enjoy taking their machines apart almost as much as actually playing them. They can happily spend an entire evening underneath a playfield armed with a multimeter, three screwdrivers and that peculiar expression of satisfaction apparently reserved for people who genuinely enjoy tracking down electrical faults.

And then there are the others.

We belong to the others.

The people who would generally rather start another game than dismantle their pinball machine. Those who don’t necessarily own a workshop full of tools, who might lack the time, technical knowledge or simply that very specific kind of courage required to bring a screwdriver anywhere near a machine worth several thousand dollars.

That doesn’t mean you have to give up on customization altogether. Some mods are simple enough to be installed by virtually any owner, provided you take your time and understand what you’re doing.

That’s the territory we’re going to explore with our Elvira’s House of Horrors Limited Edition. We’ll progressively modify three elements of the machine: the speakers, the shooter and the topper. Three different modifications, three different levels of transformation, but one philosophy: achieve a genuinely visible result without turning our gameroom into an industrial maintenance facility.

Today, we’re starting with Speaker Light Kits, illuminated rings installed behind the backbox speakers. An essentially cosmetic modification, completely unnecessary and therefore, according to the fundamental laws governing the purchase of pinball accessories, absolutely indispensable.

Before we begin, one warning. The method described here is the one we used, based on the recommendations supplied with the products. Always check that the hardware is compatible with your own machine before installing anything. And if, despite all our precautions, you somehow manage to trigger a chain reaction resulting in the nuclear fission of your Elvira, we’ll consider that you’ve accomplished something considerably beyond the scope of this tutorial.

PIMP MY ELVIRA

Customizing a modern pinball machine has become a little universe of its own. Start looking for accessories and you’ll quickly discover a fairly astonishing selection of modifications: lighting, sculptures, protectors, shooters, toppers, cabinet decorations, mechanical components and purely cosmetic additions.

Some come directly from the manufacturers and are therefore official accessories. Others come from specialist companies, where you’ll need to separate the genuine creators from those who seem to consider intellectual property more of a friendly suggestion than an actual concept. And then you have enthusiasts producing their own parts in small quantities, where, once again, there’s quite a bit of sorting to do.

All this choice is great, but it creates one fairly obvious problem: not everything is created equal. Manufacturing quality varies enormously, integration can range from gorgeous to frankly questionable, and a mod that looks fantastic in a photograph can become considerably less appealing once attached to a machine worth several thousand dollars.

For our first modification, we’re focusing on the speaker lighting of our Elvira’s House of Horrors LE. The machine already has a spectacular visual identity and its backbox lends itself particularly well to this kind of treatment. Obviously, this comes down to personal taste, but on a Limited Edition we’ve always thought it was a little disappointing that Stern didn’t include more of this kind of finishing straight from the factory.

WHAT DO WE NEED TO ORDER?

The principle behind a Speaker Light Kit is extremely simple. LED-equipped rings are installed around or behind the backbox speakers to illuminate their surrounds. Depending on the kit, the lighting can be static or animated, with different colors and sequences available.

For this installation, we chose a kit produced by a specialist manufacturer. One important point regarding the context of this article: we purchased the product ourselves and this content was not sponsored. Our choice was based on feedback from other owners and the apparent simplicity of a system that could be installed without ugly additional external wiring.

The important part, however, isn’t the name printed on the packaging. Before purchasing any kit, check its exact compatibility with your machine, its edition and the dimensions of its speakers. Just because a product is advertised for a particular Stern title doesn’t automatically mean every edition of that machine uses exactly the same configuration.

And when you’re about to connect accessories to the electronics of a pinball machine, “it should probably work” isn’t a technical procedure. It’s an act of faith, somewhat reminiscent of trusting a fart that turns out not to be empty.

CHOOSING THE RIGHT SPEAKER LIGHT KIT

At the time of our installation, three versions were available: Standard, Deluxe and Deluxe 5.25". Choosing between them wasn’t simply a question of deciding how fancy you wanted the result to be. It also depended on the machine’s configuration.

The Standard kit offered relatively simple RGB lighting with a limited selection of effects, while the Deluxe version added programmable RGB lighting and a much broader range of animations. Naturally, the price increased along with the available features.

For our Elvira’s House of Horrors Limited Edition, we selected the Deluxe 5.25", which matched the configuration used for this installation. This model also featured programmable RGB lighting with a large selection of effects.

If you’re reproducing this installation today, however, remember one basic rule: never order a kit simply because you’ve seen someone install it on a machine with the same title. Check your machine’s exact configuration and the specifications of the product currently being sold. Product ranges, components and accessories can change.

UNBOXING DAYYYYY!

The package finally arrives. It’s almost noon and naturally you’ve been waiting for the delivery driver with all the composure of a six-year-old staring at the presents under the Christmas tree. After rapidly dispensing with the obligatory social niceties with a man who clearly has no understanding of the historical significance of the parcel he has just handed you, it’s finally time to get serious.

Inside our Deluxe 5.25" Speaker Light Kit, we found a power supply, two illuminated rings, a connection cable, a remote control and an additional cable required for the final connection.

There’s nothing spectacular about the packaging. Everything we need is there and, more importantly, the installation is largely plug and play.

Well... Plug and play, give or take eight screws.

INSTALLING THE SPEAKER LIGHT KIT

FIRST THINGS FIRST: UNPLUG IT

Before opening anything, we’re going to start with the rule that should become automatic whenever you work on your pinball machine:

Unplug the machine from the wall outlet. Don’t just switch it off. Don’t tell yourself “it should be fine.” Don’t assume there’s no risk because you’re only working inside the backbox. Unplug it.

This installation requires us to work with connections inside the backbox. Simply switching the machine off isn’t the precaution we’re using here. Once the pinball machine is completely disconnected from mains power, we can begin.

STEP 1 | ACCESS THE BACKBOX CONNECTORS

Open the under-backglass door, the small access panel located in the lower section of the backbox. You’ll find several connectors inside, including the small blue connections used during our installation.

Carefully note their positions before removing anything.

If you’re new to this, take out your phone and snap a picture. It takes five seconds and can save you twenty minutes later staring at three connectors wondering which one was originally on the left.

During our installation, the two connectors on the left, associated with the white and black wires, had to be carefully removed. You can disconnect them using your fingers or a pair of pliers, but work gently. The plastic support holding the pins may move slightly as you manipulate the connectors. Don’t panic and don’t turn the operation into an arm-wrestling match. Take your time.

STEP 2 | INSTALL THE KIT HARNESS

Now take the cable supplied with the kit, recognizable in our installation by its orange connectors and additional pins. Follow the wiring arrangement specified by the kit manufacturer carefully.

The principle is to insert the new harness into the existing wiring. The original cables are then reconnected to the additional pins while retaining their respective positions, and the new harness is connected to the power supply included with the Speaker Light Kit.

This is the point where a modification that looked slightly intimidating in photographs suddenly becomes considerably more obvious once the machine is open in front of you.No soldering. No irreversible modification of the original harness. No need to summon Nikola Tesla. Insert the connectors, check everything twice and move on.

REMOVING THE SPEAKERS

STEP 3 | BRING OUT THE HEAVY EQUIPMENT

We’re now entering the highly technical stage of the installation.

Prepare yourself psychologically, because few survive this part. You will need... an 8 mm hex nut driver.

There we gooooo. Easy. Breathe. I know it can be brutal. I survived Agincourt too. (For our American readers: Agincourt was a medieval battle in 1415 where the English absolutely kicked our French asses. Yes, we’re still bitter about it six centuries later. Moving on.)

The two speakers are held in place by a total of eight screws. Remove them progressively while supporting the speakers so they don’t tip forward once released.

You may now take a few seconds to enjoy that very particular sensation experienced by the Sunday DIY enthusiast who has successfully removed eight screws without breaking anything. It doesn’t last long. But it feels good.

STEP 4 | REMOVE THE SPEAKERS

Carefully lift the speakers out of their positions. Under each speaker you’ll find the components used in the original configuration, including the foam and spacers present in the installation described here. Remove them and keep them somewhere safe.

Our advice is simple:

Never throw away original parts when installing a reversible mod.

Put them in a bag, label it and store it either inside the cabinet or with your collection of spare parts. If you ever want to return the machine to its original configuration, sell the accessory or simply undo the modification, you’ll be extremely happy to know exactly where everything is.

It’s a tiny bit of discipline that prevents several years of modifications from eventually turning into an archaeological excavation through fifteen boxes filled with mysterious parts whose origins nobody can remember.

INSTALLING THE LIGHT RINGS

STEP 5 | POSITION THE LEDs

Place the illuminated rings in their intended positions, with the LED strip oriented according to the kit’s installation requirements. On our setup, the LED strip sat against the colored plastic to diffuse the lighting correctly around the speaker.

Now place each speaker back into position.

Before reinstalling the screws, check that the light ring is correctly seated, that no cable runs underneath a mounting point and that nothing can become trapped when the speaker returns to its final position.

Gradually reinstall and tighten all eight screws. And there you have it. You have officially removed and reinstalled the speakers in your pinball machine.

Take your legally mandated dose of DIY satisfaction.

FINAL CONNECTION

STEP 6 | CONNECT BOTH LIGHT RINGS

All that remains is to connect the illuminated rings to their power supply.

In our kit, the bag containing the remote control also included a small Y-cable used to combine the two lighting assemblies before connecting them to the power system.

Connect everything according to the kit’s specified connections. The principle remains extremely simple: both rings connect to the common harness, the harness connects to the power supply and the complete assembly joins the wiring installed earlier.

Don’t simply connect everything mechanically and assume the job is finished. Before restoring power to the machine, mentally follow the entire circuit and check every connection.

Two minutes spent checking your work costs infinitely less than an electronic board.

BEFORE SWITCHING IT BACK ON: FINAL CHECK

The installation is complete, but don’t close the backbox immediately.

Check that the speakers are securely mounted, that the illuminated rings are properly positioned, that no cable is trapped behind a speaker, that every connector is fully seated and that the wiring harness isn’t hanging somewhere it could be damaged.

Also make sure you haven’t left any tools inside the backbox. Yes, that sounds obvious. Yes, somewhere out there, somebody has already closed a pinball machine with a tool still inside it.

Once you’ve completed the inspection, close the backbox properly, reconnect the pinball machine to mains power and switch it on.

AND THERE WAS LIGHT

If everything went according to plan, both speakers should now be surrounded by light.

All that remains is to grab the remote control and explore the available settings. Colors, effects and animations can all be adjusted according to the capabilities of your kit. We could obviously tell you which combination to choose, but we have to leave you some fun.

On Elvira’s House of Horrors, the result works especially well. The machine already has an incredibly rich, colorful and deliberately extravagant art direction. Adding illumination around the speakers doesn’t compete with that identity. Quite the opposite: the backbox gains presence and becomes a stronger extension of the visual excess happening down on the playfield.

Is it essential? Absolutely not.

Lazarvs

The author

Lazarvs

Fondateur de Pinball Xperience. Joueur. Collectionneur. Créateur. Le flipper comme jeu, culture et industrie. PLAY. LEARN. CONNECT.

View profile